Saturday, 20 August 2011

look, modify or combine a file



cat command Allows you to look, modify or combine a file.
Syntax 

cat filename [-n] [-b] [-u] [-s] [-v] 

filenameThe name of the file or files that you wish to look at or perform tasks on.
-nPrecede each line output with its line number.
-bNumber the lines, as -n, but omit the line numbers from blank lines.
-uThe output is not buffered. (The default is buffered output.)
-scat is silent about non-existent files.
-vNon-printing characters (with the exception of tabs, new-lines and form-feeds) are printed visibly. ASCII control characters (octal 000 - 037) are printed as ^n, where n is the corresponding ASCII character in the range octal 100 - 137 (@, A, B, C, . . ., X, Y, Z, [, \, ], ^, and _); the DEL character (octal 0177) is printed ^?. Other non-printable characters are printed as M-x, where x is the ASCII character specified by the low order seven bits.
-eA $ character will be printed at the end of each line (prior to the new-line).
-tTabs will be printed as ^I's and formfeeds to be printed as ^L's.
*If the -v is used -e and -t will be ignored.

Examples
cat file1.txt file2.txt > file3.txt

Reads file1.txt and file2.txt and combines those files to make file3.txt.
 
Now type cat without specifing a file to read
% cat

Then type a few words on the keyboard and press the [Return] key. 
Finally hold the [Ctrl] key down and press [d] (written as ^D for short) to end the input.
What has happened? 

If you run the cat command without specifing a file to read, it reads the standard input (the keyboard), and on receiving the 'end of file' (^D), copies it to the standard output (the screen). 

In UNIX, we can redirect both the input and the output of commands. 

We use the > symbol to redirect the output of a command. For example, to create a file called list1 containing a list of fruit, type   

% cat > list1
Then type in the names of some fruit. Press [Return] after each one.
pear
banana
apple
^D {this means press [Ctrl] and [d] to stop}

What happens is the cat command reads the standard input (the keyboard) and the > redirects the output, which normally goes to the screen, into a file called list1
 
To read the contents of the file, type
% cat list1

The form >> appends standard output to a file. So to add more items to the file list1, type
% cat >> list1

Then type in the names of more fruit
peach
grape
orange
^D (Control D to stop)
To read the contents of the file, type
% cat list1

You should now have two files. One contains six fruit, the other contains four fruit.
We will now use the cat command to join (concatenate) list1 and list2 into a new file called biglist. Type
% cat list1 list2 > biglist

What this is doing is reading the contents of list1 and list2 in turn, then outputing the text to the file biglist
 
To read the contents of the new file, type
% cat biglist


We use the < symbol to redirect the input of a command.
The command sort alphabetically or numerically sorts a list. Type
% sort 

Then type in the names of some animals. Press [Return] after each one.
dog
cat
bird
ape
^D (control d to stop)

The output will be
ape
bird
cat
dog 

Using < you can redirect the input to come from a file rather than the keyboard. For example, to sort the list of fruit, type
% sort < biglist 

and the sorted list will be output to the screen. 

To output the sorted list to a file, type,
% sort < biglist > slist
Use cat to read the contents of the file slist



No comments:

Post a Comment